my "audiolab" abstraction library is now available on deken. You'll need Pd-0.50 or later to run this.
Please report any bugs on github: https://github.com/solipd/AudioLab

here is a picture to draw you in (:

Edit:
list of objects:

Soundfle processing
pp.sfplayer~ ... variable-speed soundfile player
pp.grainer~ ... granular sampler
pp.fft-stretch~ ... pvoc time stretching & pitch shifting

Spatialization
pp.pan~ ... constant power stereo panning
pp.midside~ ... mid-side panning
pp. spat8~ ... 8-channel distance based amplitude panning
pp.doppler~ ... doppler effect, damping & amplitude modulation
pp.dopplerxy~ ... xy doppler effect

Effects
pp.freqshift~ ... ssb frequency shifter
pp.pitchshift~ ... pitch shifter
pp.eqfilter~ ... eq-filter (lowpass, highpass, resonant, bandpass, notch, peaking, lowshelf, highshelf or allpass)
pp.vcfilter~ ... signal controlled filter (lowpass, highpass, resonant)
pp.clop~ ... experimental comb-lop-filter
pp.ladder~ ... moogish filter
pp.dynamics~ ... compressor / expander
pp.env~ ... simple envelope follower
pp.graindelay~ ... granular delay
pp.rev~ ... fdn-reverberator based on rev3~
pp.twisted-delays~ ... multipurpose twisted delay-thing
pp.shepphaser~ ... shepard tone-like phaser effect
pp.echo~ ... "analog" delay

Spectral processing
pp.fft-block~ ... audio block delay
pp.fft-split~ ... spectral splitter
pp.fft-gate~ ... spectral gate
pp.fft-pitchshift~ ... pvoc based pitchshifter
pp.fft-timbre~ ... spectral bin-reordering
pp.fft-partconv~ ... partitioned low latency convolution
pp.fft-freeze~ ... spectral freezer

Misc.
pp.in~ .... mic. input
pp.out~ ... stereo output & soundfile recorder
pp.out-8~ ... 8 channel output & soundfile recorder
pp.sdel~ ... samplewise delay
pp.lfnoise~ ... low frequency noise generator
pp.spectrum~ ... spectrum analyser
pp.xycurve

@solipp said:

pp.phiverb~

what can you tell us about this new object? Where is the model from, what is it based on? I'm interested in reverb design

thanks

@porres
It is based on this talk by Geraint Luff:

However, the basic structure is the same as in rev3~, early reflections are fed into a 16-channel fdn. Delay times are selected from a table of prime numbers. The "secret" lies in the mixdown of the 16 fdn channels to stereo. It was more or less trial and error, adding and subtracting the signals and listening what sounds good.

nice, thanks

A new version is now available on deken, v0.63.

added 2 new objects:

pp.pantd~ stereo panner with time delay
pp.grainer-mc~ a granular sampler with multi-channel signal outlet

A new example 15-train_of_sounds.pd showcases the use of some audiolab abstractions with pd's multi-channel signal connections.
Example 14-glitchfest.pd is also new and just a lot of fun to play around with.

fixed some bugs as well.

Happy patching!

Simply Amazing thanks!

@solipp said:

https://github.com/solipd/AudioLab

Fantastic patches!

I can't figure out how to use the sidechain in the compressor. There's no key input, just an enelope out. Should I feed the compressor an audio signal somewhere or an envelope? I am confused. What is the sidechain preset for? Can anyone help? Thanks.

@qhr33k Thanks!

about this sidechain thing; yes you would need to feed the compressor an audio signal and use the sidechain output to let's say duck the tail of a reverb (that's just an example, you can do whatever you want with this). In this case you would multiply the 100% wet reverb with the signal from the sidechain outlet of the compressor like this:

sidechain_compression.pd

The presets are more or less didactic, you can use them as a starting point and then change the parameters until they fit your needs. In the case above you'd use the "compress" preset. I think what confuses you is the preset "Env.follow(sidechain)". This one is an envelope follower, the comment (sidechain) hints that the envelope is the signal from the sidechain outlet. Hope that makes sense?

Thanks a lot! i was looking for that patch point inside the compressor for days. I would have never come out with the solution of simply putting it outside the comp without you pointing to it. Thanks again your patches are gold.

Version 0.70 is now available on deken.

I added some simple but convenient objects:

pp.amp~ a simple signal multiplier
pp.adsr~ adsr/adr envelope generator
pp.xfade~ signal crossfader
pp.shiftlfo~ a LFO that can generate irregular rhythmic patterns

pp.dynamics~ now has an option to enable feedback compression

Some parameter sliders are now colored light orange in the GUI. This indicates that the slider does not cover the full range of the parameter and is intended to encourage experimenting with values that are above or below the range of the slider.

fixed some minor bugs.

Happy patching!

I just downloaded Audiolab to get pp.spectrum~ and I love it! Thank you for making this.

I love the way that Audiolab modules look and work. Thank you for making it! I'm trying to use pp.eqfilter~ as a notch filter. When I close and reopen the patch, I have to reset notch and the other parameters. Is there a way to get it to remember my settings? Thank you!

@jamcultur thanks! You can save any of these objects with a message [save 1( to the rightmost inlet. Then use [recall 1( to retrieve your parameter settings. You can save up to 21 presets this way. This is also documented in the help files and in Examples/01-basics.pd

@solipp Thank you!

Hi, I have trouble installing latest 0.71 version on Deken. It cannot create folders Examples and audio and cannot copy any stuff into them.
0.70 is OK
Thanks

@jyg someone reported a similar issue with the deken installation on a Windows OS on github. I can not reproduce this on Linux and i don't know what could be causing it, so my suspicion was that it is somehow related to Windows security permissions. Are you using Windows? Does this happen with other libraries as well? Unfortunately, there is not much i can do about it, but i'll test as soon as i have access to a Windows machine.
For now, if you want to stay up to date you can download from github and set the path manually in pd settings.

Edit: just saw that you created another issue about this on github. I'll close it because it is not related to the development of this library, but we can continue the conversation here.

Sorry, I mistook the OSes. On Windows it's OK, although I get some error messages (see video below).
At end, the files and folder structure are copied.
BUT on MacOs BigSur The folder structure is not copied, neither the contained files (Examples and audio)

audiolab-installDeken.mp4

@jyg i just uploaded a new version 0.71.1 to the deken repo. Can you test if this works for you?

Unfortunately it doesn't work on macOS with plugdata. But I have to deeper check if this is related to plugdata / puredata or to the specific OSX platform I use. (I won't have any access to it until january 2026)

Thank you this is very cool. I can see myself making use of many of these objects

I just installed 0.71.1 on Windows 11, and it seems to be working fine.