Hey guys!

I'm looking for a simple interface to load lot's of files (IRs) into pd. I need each data in an own table with special parameters and the correct name (means table 1, table 2 etc)! I think have a clue how I request the data via automation but how can i create the tables automatically (with the right parameters and names)?

thx for your help

Hey,

I want to get a graph from a Impulse Response wav file after rfft conversion.

I want to do this with the l02.Hann.window.pd and the integrated pd fft-analysis
As expacted the patch works fine when i get in with the preset signal which is a osc~ signal. But how can I get in with a wav. file?

my first idea was that i do it with:

[open ... (
|
[readsf~]
|
pd fft-analysis

is that okey? my problem is that i can see no graph and i'm not sure why? too less gain from the impulse response?!

thx for your help

Hey,

can anyone explain me how i can load a txt. file contains int. in a table (array)

i'll do it with: a bang => openpanel => ?

I dont have a clue how i can store it to the table?

please help me!

thx

Hey,

i've a question and i hope you can give me an answer.

i'm new in programming and working with pd and i want to built a programm where i habe any kind of sliding controller and the value of this controller should reference to an objeckt in a table, list or index.

So if the slider value is 1 then a message should be print with the first element of the list.
Value 2 => list object 2
...
....
.....

you see what I mean.

So I'm not really sure what object list, table or index fit for this action and how i can reference form the slider value to the element in the list?????

thx for your help

hey guys

I want to implement the freeverb object. I downloaded it and now i'm not quite sure where i should install it (mac user!)

When i oben the freeverb patch and create the freeverb object in another patch everything is fine. When i close the freeverb patch the freeverb object in the other pathc doesn'T work any more?!

can some please tell me how this works?!

thx

anyone?!?! please?!?!?!

hey nau,

done it with a loop and works as i expacted!

thx for help think the patch is running as i want but i have to do a few more tests but it looks good!

thx nau!

by the way i managed the $0 and $1!

well i don't no but i can't find the iem libray at my system! Perhaps it isn't installed and i have to download it otherwise i have to do it by the loop!

schurl

thx nau,

have another question^^

i got the array $0-magnitude in you patch! Just for testing i want to take this array and write it in another array. so that i have two arrays with different names but with the same content.

i tried it with

[tabreceive~ $0-magnitude]
|
[tabwrite~ $0-test]

so i want to see how i can transfer array content from one array to another...as i said just for testing!

thx

ahja thx nau

but now i have a question the $1 means that it gets exchanged by a number which comes from another input?!
Does this works also for [tabreceive~]? so that i can say [tabreceive~ir$0] and change the $0 to $1, $2 etc. via a number box or a slider?!

thx

okey

well there a about 150 - 200 IRs I want to handle!
well the idea is to control the IRs via a slider. this sliders outputs a number/index wich can be used to manipulate the adressing of the tabrecvieve object?!
this also means that I have this many many IRs in a seperate table with numbers from 1 - x????

schurl

well one additional question to this:

is it possible to write such a table in another table/array!
The idea is that i have many of this IRs and want to store them in an array for a later fft with another signal.
With a slider it should be possible to switch between the differen IRs of the array and use them for my fft. I hope my idea is clear?!?!^^

thx

Hey man,

thx for the help i think this is the solutuion! Thx you sou much!

hey,

more about my problem when the resize works but when i want to read my txt into the table there comes this message???

"read 0 elements into table of size 20"

anyone???

that will be okey, there are just numbers but something is still wrong. Here is my code I thin there is an error in the building order or a problem that my dont't write into my

i also have a table

thx... now i can read the txt but in the table there are just zeros is this because it's not resized? How i can/should resize the table?!